怎樣有效率的批量清洗五金件呢？人工清洗是費時又費力的，現在用工成本又高，所以，五金件清洗日漸由91视频破解版來完成，尤其是數量較多，結構複雜時。下麵來講講91视频破解版清洗五金件的技巧。

How to efficiently clean hardware in batches? Manual cleaning is time-consuming and laborious, and now the labor cost is high. Therefore, hardware cleaning is increasingly completed by ultrasonic cleaning machines, especially when the number is large and the structure is complex. Let's talk about the skills of cleaning hardware with ultrasonic cleaning machine.

91视频破解版的優勢在於其清洗方式是將五金件浸沒在清洗槽內液體中，利用超聲波的高頻率，通過換能器轉化為高頻動能，然後作用於清洗槽中的液體介質，使液體產生空化作用，不斷的形成無數個細微氣泡，並迅速爆裂，產生衝擊力衝擊物件表麵，使表麵汙垢脫離，從而達到清洗的效果。

The advantage of ultrasonic cleaning machine is that its cleaning method is to immerse the hardware in the liquid in the cleaning tank, use the high frequency of ultrasonic wave, convert it into high-frequency kinetic energy through the transducer, and then act on the liquid medium in the cleaning tank, causing the liquid to produce cavitation, constantly forming countless fine bubbles, and rapidly bursting, generating impact force to impact the surface of the object, so that the dirt on the surface is separated, so as to achieve the cleaning effect.

這樣一來，隻要是水能接觸到的部位都能清洗幹淨，不留死角。並且同時作用於五金件的各個部位，不像人工那樣一點點的清洗，因此，效率高。

In this way, as long as the parts that can be touched by water can be cleaned, leaving no dead corners. It also acts on all parts of hardware at the same time, unlike manual cleaning, so it has high efficiency.

使用91视频下载大全為五金件除蠟、除塵時，可以用普通水加一些洗衣粉清洗即可，如果是除油，建議添加些除油的清洗劑，大批量清洗時可以給91视频破解版定製加裝濾油器，這樣水可以循環使用，不用頻繁換水。

When using ultrasonic cleaning equipment to remove wax and dust for hardware, you can use ordinary water and some washing powder for cleaning. If it is oil removal, it is recommended to add some degreasing cleaning agents. When cleaning in large quantities, you can customize and add oil filters to the ultrasonic cleaning machine, so that the water can be recycled without frequent water change.

而除鏽則有專門的除鏽劑。對於清除五金件上的碎屑，如果是盲孔可能效果不太好，因為超聲波清洗主要是將表麵的汙垢脫離，但沒辦法清除掉。較短的通孔則完全沒有問題，可以將孔裏麵的碎屑清除掉。

There is a special rust remover for rust removal. For the removal of debris on hardware, if it is a blind hole, the effect may not be very good, because ultrasonic cleaning is mainly to separate the dirt on the surface, but there is no way to remove it. There is no problem with the shorter through hole, and the debris in the hole can be removed.

關於五金91视频破解版的頻率，一般來說40KHz是通用頻率，可以勝任五金際件清洗工作，這在眾多客戶的實使用中也得到證實。但有些較複雜的精密的五金件可以考慮更高頻率，如80KHz，而有些五金件則相反，需要28KHz，這主要是針對除鏽或者碎屑較多的情況。更多相關內容就來網站www.bolomie.com谘詢吧。

As for the frequency of hardware ultrasonic cleaning machine, generally speaking, 40KHz is the general frequency, which can be competent for the cleaning of hardware parts, which has also been confirmed in the actual use of many customers. However, some complex and precise hardware can consider higher frequency, such as 80kHz, while some hardware, on the contrary, need 28kHz, which is mainly aimed at the situation of rust removal or more debris. For more information, please visit www.bolomie.com.